MZ ROLA Posted November 17, 2009 Report Posted November 17, 2009 some temporary panel/paint work to stop it rusting away .. motor - 12a bridgeport, nikki 4 barrel, electronic dizzy leads - 9 mil eagle leads oil cooler- rx2 oil cooler scatter sheild rad fan s1 radiator rad hoses belt, temp sendor adapter ect coils - bosch gt40 new dipstick from mazda driveshaft loop engine rubbers - solid mount style engine mounts - made by kiwi re crossmember and gearbox crossmember 4 Puk clutch kit engine loom - made by me motor and s2 rx7 box ready for ins brakes - s4 rx7 hubs new braided lines and pajero master to suit new brakes ke30 handbrake and s2 rx7 shifter fc rx7 handbrake cable wheel selection i love tarmacs interior - suede door skins, mx5 seats, evo 1 center console, digital speedo, tacho, smoked guages and a momo wheel Quote
13BT_KE20 Posted November 17, 2009 Report Posted November 17, 2009 nice work mate, looks like your doing the conversion properly with all the supporting gear. Only thing i see breaking would be your diff, got any plans to upgrade? Another rota rolla is never a bad thing Quote
MZ ROLA Posted November 17, 2009 Author Report Posted November 17, 2009 nice work mate, looks like your doing the conversion properly with all the supporting gear. Only thing i see breaking would be your diff, got any plans to upgrade? Another rota rolla is never a bad thing it got a hilux diff and i even have a spare head haha :blush: Quote
guitar mad Posted November 17, 2009 Report Posted November 17, 2009 awesum work there!! great to see another rotor going into a corolla, you from nz yeah? still lots of rx3s and rx2s over there??? I'm from wellington last time i was there there were rotors every where!! haha love em, good luck with the hole project looks like you have it in control! wish i could say the same about my sr20 rolla hahahaha :blush: go the rollas!!!! Quote
MZ ROLA Posted November 17, 2009 Author Report Posted November 17, 2009 haha thanks :P yes there are quite a few old rotarys around here in auckland :D i think i was looking at the sr20der rolla just before in this section, looks like a big mission haha how much clearance you go between motor and firewall :blush: Quote
MZ ROLA Posted November 17, 2009 Author Report Posted November 17, 2009 also i need some help setting up my fueling, i have got a holley blue fuel pump and a holley reg, do i need to run a return line?... would i benefit from using the factory line as a return and upgrading the main line (if so what should i upgrade to size, rubber/metal ect) cause if I'm not mistaken my car does not have a factory return thanks Quote
guitar mad Posted November 17, 2009 Report Posted November 17, 2009 (edited) haha thanks :P yes there are quite a few old rotarys around here in auckland :D i think i was looking at the sr20der rolla just before in this section, looks like a big mission haha how much clearance you go between motor and firewall :blush: my engines not quite in yet just sitting waiting .... so much to do! haha but yeah don't think theres going to be much clearance there maybe 5 -10 mm if that,not to worry my pics are in the gallery under jdm55,,, yeah you should definatley upgrade your fuel line 8-10 mm should be plenty, use steel bundy line,should be able to get it at repco or a hose joint over there,can't remember if rotors use a return line been a long time since played with them,i think some where i read you can blank off the return on the carb if its not already got a blanking plate on it,??? not 100percent ,but your holley should do the trick , keep up the good work love to see pics!!! Edited November 17, 2009 by guitar mad Quote
guitar mad Posted November 17, 2009 Report Posted November 17, 2009 (edited) actualy have you got any more pics of the front brakes and strut set up? still struggling to find a practical brake upgrade for my beast,any infos be great cheers Edited November 17, 2009 by guitar mad Quote
MZ ROLA Posted November 17, 2009 Author Report Posted November 17, 2009 (edited) I'm going to be putting my brake hoses on in the next few weeks so ill get you some getter pics then :blush: msn .. [email protected] Edited November 17, 2009 by MZ ROLA Quote
Rolliac Posted November 18, 2009 Report Posted November 18, 2009 Nice work dude. I like the wheels too. Quote
furryfrog Posted November 24, 2009 Report Posted November 24, 2009 This thing looks like a load of fun, The FC callipers with the MC will make the car stop great. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.