My 1976 Ke30

[Evan G]

did you have to trim some gaskets?

[-=KE30=-]

did you have to trim some gaskets?

 

i had to cut a small bit of the throttle body gasket but it was only one corner to make it neat :)

[-=KE30=-]

Not much has been happening latly..just been doing bits and pieces on the paint/rust.

I did however get these from Mr SLO 030 :y:

 

 

 

Random photo lol

 

Cheers :P

[-=KE30=-]

Been so long since I updated so as it stands at the moment it has

 

new Goss fuel pump

King springs lowered

Monroe GT gas shocks (fronts)

new Front end bush kit

Brand new stock carb

the front calipers had a seal kit put through them and cleaned

new front pads

new brake lines

new brake rotors

new headlights with a semi sealed beam and just some h4 globes, within the next week i will be rebuilding the headlight loom with relays etc to make them brighter

and lastly new crome number plate lights

I think thats it for the moment.

 

In a few weeks i will start sanding it and hopfully respray it

 

Cheers Josh

[JJT036]

Venetians and SLAM! :yes:

 

Looks good mate. :y:

 

Josh :cool:

[bmxsexmonkey]

I like what you have done, nice clean and simple. I applaud your efforts in rebuilding that carby. I had twin aisan carby's and the rebuild kits. I said "f@$k that" after looking at the diagram and sold them haha

[jaygore]

Venetians and SLAM! :yes:

 

Looks good mate. :y:

 

Josh :cool:

 

hell yea totally agree here...

 

Mine is getting picke up today after being slammed =] and I have venetions, they really do set it off nicely

 

Also I am loving those wheels!!

[ijg033]

Nice clean looking 30 , wheels suit ,

 

Cheers

 

Dave

[-=KE30=-]

since last update have been very busy, unfortunately not alot of it was with rolla but I have done a bit.

 

I put Monroe GT gas shocks in the rear so gas shocks front and back big improvement.

I put in an electric dizzy from kemotorsport

also i 3/4 exhaust from extractors back, extractors have been flanged with a tri-chamber muffler and a 2" crome dumpy tip. sounds sexy ^_^

I got bridge-stone turanza AR10's yesterday so good so far

 

rear breaks will be my next focus as there isn't much left of them lol

 

cheers

 

 

 

[lammi]

Nice build mate. looks amazing :)

[Oh-KE]

Car looks great dude, must not be too far away from being on the road??

[-=KE30=-]

Thanks guys. Yeah Chris its close to been on the road for good. Can't wait :P

[-=KE30=-]

Recently been spending lots of time and money on this car since last update

 

new masercylinder and rear brake shoes and rear cylinders

 

the stock carb was jetted and tuned by the guys at Adelaide carb service :y: top job

 

have replaced inner and outer tie rods

pitman arm

idler arm

put a 620cca battery in her

with a HEC716 bosch coil to drive the elec dizzy

2x 10" subbies in custom box

6x9 on parcel shelf

6.5's in doors

jvc headunit and a 4 channel 600watt amp to power this badboy

 

also just rebuilt my 4k specs as followed

head work-full rebuild new valves, guides, shaved

block was dipped, honed, faced. It now reps 0.30" oversize pistons with ACL rings

all parts were pulled down, measured, sand blasted and put back together with all new parts

cam regrind, crank regrind, rebuilt oil pump, double row timing chains, re fabed welsh plugs, new clutch,machined flywheel, new bearings throughout the entire engine

thermostat was also replaced with an aftermarket radiator.

 

still running the 4 speed for now but soon to be 5.

will post some pics over the next few days of the engine build and the car as it stands now :cool:

 

atm drivin her everyday and lovin it

 

cheers Josh

Edited October 16, 2011 by -=KE30=-

[-=KE30=-]

the engine as i bought it.

 

to this

 

 

[-=KE30=-]

big ass fire ball came out the exhaust.. timing way out lol