Kid-Ae Posted April 8, 2008 Report Posted April 8, 2008 motors are supposed to be like that to hide any leaks :dance: Quote
Des Posted April 21, 2008 Author Report Posted April 21, 2008 (edited) I pick up my engine from road and track tomorrow. I just got them to clean it and measure it up for me as i decided to build it myself seeing as ive got a worked 18RG to build now too :dance: Got a set of 20v factory headers today for my 16v, Will need to be re drilled but I'm cool with that as they should flow a bit more than the factory 16v cast manifold. Edited April 21, 2008 by AE70 Quote
Trev Posted April 21, 2008 Report Posted April 21, 2008 Building it should be a good project for you and thanks i had alot of fun cleaning it. Quote
Des Posted April 22, 2008 Author Report Posted April 22, 2008 (edited) Got the engine back today. The bores are worn so i will need to go 20 thou over sized pistons. Crank looks good, No scouring at all on the journals just a little but on the rear crank seal surface. Oil pump is also worn but I'm not worried about that as I'm getting higher pressure pump with stronger gears. The pistons look new, Not a single wear mark on them just a few marks from them being chemically cleaned. Mum cracked the shits because i have the Crank, Rods, Pistons, Oil pump and a few other small bits stored in my bedroom and it now smells like CRC, Need to open a window me thinks. 7 rib block Pulleys, Flywheel etc. 42mm crank, Rods, Pistons etc. Bigport 3 rib rods vs smallport 7 rib rods. Pretty clean for used pistons. Just some marks from the chemical cleaner but they wipe off. Edited April 22, 2008 by AE70 Quote
Trev Posted April 22, 2008 Report Posted April 22, 2008 Pretty clean for used pistons. This might explain that... Before: After: The crank was very clean, All i did was removed the oil from it. Quote
Des Posted April 24, 2008 Author Report Posted April 24, 2008 Yeah they still look good, I was expecting scuff marks on the skirts but its clean as. I need to go 20" over sized pistons but i don't know what brand to stick with ? Quote
Des Posted May 2, 2008 Author Report Posted May 2, 2008 Blacktop 20v quad throttle bodies are on the way. Quote
Des Posted May 11, 2008 Author Report Posted May 11, 2008 Most likely getting a newer car in the coming months so not much will happen with this other than all the motor bits being put away properly. I'm not going to sell it but store it. Might be pimpin the Beauy hoes from a bagged crown soon :D Quote
Trev Posted May 11, 2008 Report Posted May 11, 2008 Most likely getting a newer car in the coming months so not much will happen with this other than all the motor bits being put away properly. I'm not going to sell it but store it. Might be pimpin the Beauy hoes from a bagged crown soon :D Ha, Is that the one you had lined up a while ago? Quote
Des Posted May 14, 2008 Author Report Posted May 14, 2008 Ha, Is that the one you had lined up a while ago? Nah that one was flogged out. Quote
Des Posted May 18, 2008 Author Report Posted May 18, 2008 Head gasket blew today so I'm back in the Ke70. 165/70/R13's tyre's on the rear are fun. Quote
Des Posted May 27, 2008 Author Report Posted May 27, 2008 Decided to rebuild it to stock form. So the quads and headers are for sale and the toda stuff etc has been canceled. Quote
Des Posted June 10, 2008 Author Report Posted June 10, 2008 Got all the bits i need to rebuild it, Pistons, Bearings etc. Cost me $950 for everything. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.