drc_ke20

thats super horny hot!!!

you saved $$$$ with self diagnosis and repair instead of sending an auto electrician to find and fix the problem,well done :dance:

exactly the same way i clean muddy bottles......it does work!

not too bad....but its got a lancer front bar,rear end of RX8,front guards of CX7,350Z roof and doors with Aurion h/lights...... :y:....it would be nice to see it in reality??? how much would this be??i might buy one if i still have a job then... :dance: maybe?

remove the whole radiator and give it to your local radiator specialist roughly about 50 bucks for a full service.they will remove the top tank of your radiator and clean it properly,i think your better off this way instead of just flushing it??? :dance:

ask your mates,maybe they have a relative that is a panel beater???or maybe your dads mates????

try hitting the screw head flat and like mr ae71 said use some wd40 and start again. have you tried it with small vice grips??

sorry :lolcry: my bad its 4 x 100 and 4 x 114.3 fitment

use a rattle gun or breaker bar,if not use a your ratchet and put a pipe over it for leverage as you do that stop the flywheel or ring gear from spinning with a flat bar on the tooth gear. *N.B. screw back one of the bell housing bolt on the block as a counter pivot aswell for you flat bar to rest on. hope it helps,good luck!

very nice mate! OCC`s got nothing on your bikes!!! your kicking rear end! :lolcry:

i wish i live in SA! mom can we move to south australia.....mom said "NO"..... :lolcry:

just tell them your vin number and all the details of the car should be there.if not say your engine code(4age) aswell. :hmm:

remove steering shroud,remove two phillips head screw at the bottom of the barrel,get a pin punch and a medium size hammer slowly tap anti clockwise the two flat looking screw heads or maybe tappered shape.make sure you make a pin punch mark to the top of the screw head so you can start from there.to install just reverse the procedure.hack saw the top of the flat screw so you just use a flat blade screw driver to tighten them back on. hope this helps you and good luck!

downside is you cannot drive your car on everyday situation only on event or club meets???

bodykits for a excel??its craptaculos!!! :hmm: jap cars are kool and made with pride.....korean umm....disposable cars..sht box......???

I'm running it on 4 x 114.3 but i can run it on 4 x 110 aswell (multi fit rims,8 hole rims). i got it for $800 set of rims plus tires.i just don't know how much is postage to where you are?? JDM yard is base here on Revesby Sydney.

this is going to be one sick KE70...can't wait for the finish project :hmm:

hoping nothing is stuck in the flywheel or ring gear?? try turning the engine at the front crank bolt with a ratchet,hope its free?? what it could be :hmm:???

looking good :hmm: what color is this car going to be again? can't wait to see it :no2:

i got this on my KE20 aswell (S/M 501) 15 x 8 i got about 3 inches of dish on this,freaking kool!! HOT green wagon by the way and nice AE71!

hey mate best bet to have the right ignition coil for your rolla is to ring your nearest Toyota dealership and get a genuine part,might be costly but you have the right part. (make sure you give them you chassis or vin number) hope this helps you?? :hmm:

sweet ride and very nice indeed!!! porn star video :hmm: !!!! 10 ********** stars!!

i like the 1st picture better its got that midnight run character on it. light contrast is perfect and its very sharp,its like from a movie scene! very good pictures. :P

here is the contact details and address :D Brock Flanagan Operations Manager Mazfix Performance PHONE:07 3341 11 11 www.mazfix.com 48 SMALLWOOD STREET UNDERWOOD QLD 4119 AUSTRALIA